Por favor, use este identificador para citar o enlazar este ítem: http://repositoriodigital.ipn.mx/handle/123456789/8178
Título : REFORZAMIENTO DE ALEACION Ag-Sn CON NANOPARTÍCULAS DE PLATA: APLICACIÓN ODONTOLOGICA
Autor : Dr. Martín Martínez., Eduardo San
Dr. Barceló Santana, Federico Humberto
Ortega Arroyo., Lesli
Palabras clave : Ag-Sn
NANOPARTÍCULAS
PLATA
Fecha de publicación : 27-jun-2011
Resumen : In this research, the addition of silver nanoparticles, obtained by a green synthesis, on AgxSnx alloy was studied. The alloy was fabricated using the loss wax methodology. The response surface methodology was selected to evaluate the effect of studied factors on the response variables. The characterization of materials was realized through X-Ray diffraction, Scanning Electron Microscopy and Transmission Electron Microscopy techniques. Also, tensile stress, hardness and corrosion tests, were done follow ISO and ADA standards. Thermal diffusivity of the material was obtained using the open cell photoacoustic method . The results of X-ray diffraction confirm the crystalline nature of the AgxSnx alloy as well as its hexagonal structure. Also, the presence of a new phase was identified adding the silver nanoparticles in the AgxSnx alloy with a face centered cubic (fcc) structure. The tensil stress test showed that increments in the nanoparticle and silver content in the alloy reduced the elongation of the material. Meanwhile reducing the nanoparticles content and increasing the silver content the maximum strength. SEM images allowed identified the type of mixed failure. Through chemical etchants was obtained the microstructure of the material observing that material presented refining of size grain. In the grains and grain boundaries silver nanoparticles were deposited causing the formation of microholes in the grain. This fact supposes the appearance of failure transgranullar. It was possible to change the hardness of the obtained materials from 500 VHN to 1200 VHN approximately. The values of thermal diffusivity were higher than that reported by pure silver (1.7 cm2/s). through corrosion test was possible to observe that the addition of silver nanoparticles maintained the color and brightness of the material and the loss weight was lower, indicating the resistance to corrosion of the obtained materials
Descripción : En la presente investigación fueron estudiados el efecto de la adición de nanopartículas (NPs) de plata, obtenidas a través de un método ecológico de síntesis sobre la aleación AgxSnx. La aleación de estudio fue fabricada a través de la técnica de cera perdida empleada. La metodología de superficies de respuesta fue seleccionada para evaluar el efecto de los factores (concentración de nanopartículas de plata y concentración de plata respecto al estaño) y niveles (0 a 0.05% p/p de nanopartículas y 0.91 a 1.0 % p/p de plata) que más afectan las propiedades de esta aleación. Las técnicas para caracterizar las aleaciones fueron Difracción de Rayos X (DRX), Microscopia Electrónica de Barrido (SEM) y Microscopia de Electrónica de Transmisión (TEM). También se realizaron pruebas de Tracción, Dureza y Corrosión del material todo bajo normas ISO y ADA. Además de emplear la Celda Fotoacústica Abierta (FA) para determinar la difusividad térmica del material. Con los resultados de DRX fue posible comprobar la naturaleza cristalina de la aleación AgxSnx así como su estructura Hexagonal. Además se identifico la presencia de una nueva fase al adicionar las nanopartículas de plata a la aleación AgxSnx con una estructura Cubica Centrada a las Caras atribuida a la presencia de estas NPs que varía su intensidad dependiendo de su concentración en la aleación. Las pruebas de tracción mostraron que al incrementar el contenido de NPs y plata en la aleación reducimos la elongación. Mientras que al disminuir el contenido de nanopartículas e incrementar el contenido de plata se incrementaba la resistencia al esfuerzo ultimo del material. Por SEM después de las pruebas de tracción se identificó el tipo de falla que es mixta. A través de un ataque químico se obtuvo la microestructura del material donde se observo que el material presento refinamiento del tamaño de grano. En los granos y en los límites de grano se depositaron las NPs lo que provoco que en el grano se indujera microhuecos; de los cuales se concluye que la falla pudo ser transgranular. De los materiales obtenidos logramos modificar la dureza de 500 VHN hasta 1200 VHN aproximadamente. A través de las pruebas de Difusividad térmica se logro obtener valores por arriba del reportado para plata pura (1.7 cm2/s). Por la prueba de corrosión se observo que la adición de NPs Ag, mantuvieron color y brillo del material y se tiene la menor pérdida de peso, indicando que se tienen materiales más resistentes a la corrosión.
URI : http://www.repositoriodigital.ipn.mx/handle/123456789/8178
Aparece en las colecciones: Mediateca

Ficheros en este ítem:
Fichero Descripción Tamaño Formato  
TESIS REFORZAMIENTO DE ALEACION POR LESLI ORTEGA ARROYO.pdfREFORZAMIENTO DE ALEACION Ag-Sn CON NANOPARTÍCULAS DE PLATA: APLICACIÓN ODONTOLOGICA7.71 MBAdobe PDFVisualizar/Abrir


Los ítems de DSpace están protegidos por copyright, con todos los derechos reservados, a menos que se indique lo contrario.